Search results for 'Drive' and 'x'='x and 1>1'
-
-
An error occurred, please try again later.
Loading, please wait...
-
- Sturdy, elegant valve series that is easy to operate
- Port G1/8, G1/4, G3/8
- Plug connector 4, 6, 8, 10, 12 mm
- Flow rate 600 ... 2400 l/min
- Pressure range -0.9 ... 10 bar
- Temperature range −10 ... +60°C
- Voltage 12, 24 V DC, 24, 110, 120, 230, 240 V AC
- In-line valve
- Electrically actuated, piloted
- Pneumatic and mechanical spring return
Learn More
-
- Port Rp 1/4, Rp 3/8, Rp 1/2, Rp 3/4, Rp1, Rp1 1/4, Rp1 1/2, Rp2
- Flow 5,9 ... 243 m³/h or 98 ... 4050 l/min
- Pipe thread to EN 10226-1
- 2-way and 3-way with L-shaped and T-shaped bore
Learn More
-
- Nominal width: DN ¼" ... 4" (ISO 5211)
- Thread to ANSI B 1.20.1 (NPT)
- 2-way; 2-way manual, with lockable hand lever
- 3-way, L and T hole as horizontal version
Learn More
-
- Nominal width: DN ½" ... 4" (ASME), ½" ... 2½" (ISO), ½" ... 2½" (DIN)
- Long welded ends to ASME-BPE and ISO 1127
- Clamping sleeves to ASME-BPE and DIN 32676-B
- Electro-polished surfaces to SFV4
- PFTE seal with minimal dead space
- 2-way shut-off valve
Learn More
-
- Connection G1/8, ISO size 18mm (02); G1/4, ISO size 26mm (01), ISO size 42mm (1), ISO size 52mm (2)
- Flow rate 500 ... 2900 l/min
- Voltage 24 V DC, 110 V AC
- Sub-base valve
- Solenoid actuated, pilot actuated
- Manifold sub-bases
- Intermediate pressure regulator plates.
- Flow control plates
- Vertical pressure shut-off plates
- Vertical supply plates
- 90°-connection plates
- Individual sub-bases.
Learn More
-
- Connection G1/8, ISO 02; G1/4, ISO 01
- Flow rate 500 ... 1000 l/min
- Sub-base valve
- Sub-bases
- Manifold sub-bases.
Learn More
-
- Connection G1/4, ISO1; G3/8, ISO2; G1/2, ISO3; G3/4, ISO4
- Flow 1 200 ... 6 000 l/min
- Voltage
- Sub-base valve
- Electrically actuated, piloted
- Pneumatically actuated
- Sub-bases
- Manifold sub-bases
- Throttle plates
- Intermediate pressure regulator plates.
Learn More
-
- Voltage 12, 24 V DC, 24, 110, 230 V AC
- Connection plate valve
Learn More
-
- Connection G1/4
- Flow 900 ...1 000 l/min
- Voltage 12, 24, 42, 48 V DC, 24, 42, 48, 110, 230, 240 V AC
- Namur port pattern to VDI/VDE 3845
- Electrically actuated, piloted
- Mechanical spring return
- Can be changed from 5/2 to 3/2-way function
- Explosion protection according to ATEX
Learn More
-
- Barbed fitting connection 3 mm
- Flow rate 60 l/min
- Pneumatic-mechanical sequencer with 12 steps and start logic circuits
- Ready-to-install sequence controller
- Acknowledgement-controlled motion sequences
Learn More
-
- Connection G 1/8
- Flow 50 l/min
- Two-hand actuation.
Learn More
-
- Connection: G¼, G¼, NPT¼ and Namur
- Voltage: 24, 110, 230 V DC, AC, UC
- Explosion protection: EX me and EX d, ATEX
- Robust and corrosion resistant thanks to hard-ematalised surface
- SIL certificate for ESD applications.
Learn More
-
- Internal/external pilot air reversing via internal shuttle valve
- Valve function 3/2, 5/2 monostable and bistable
- Port G1/4, G1/2, NPT1/4, NPT1/2 and Namur
- Voltage 24, 110, 230 V DC, UC
- Explosion protection EX me and EX ia, ATEX
- Sturdy and corrosion-resistant thanks to tough enamel surface
Learn More
-
- Individual valve for clean design,
- Can be used in the food zone (based on the EN 1672-2 standard)
- Connection G1/8
- Push-in connector 6 mm
- Flow 300 ... 650 l/min
- Voltage 24 V DC
- Sub-base valve
- Electrically actuated, piloted, pneumatic spring return
- Connection via cable end
- Signal status display with LED
- Individual sub-bases
- Manifold blocks.
Learn More
-
- For servopneumatic applications with CPX-CMAX and CPX-CMPX
- Connection: G1/8, G1/4, G3/8
- Flow rate: 350 ... 2000 l/min
- 5/3-way proportional directional control valve, closed
- Fully digitised, with integrated pressure sensors
- Diagnostic capabilities
- With switching output for actuating a clamp-type brake unit
Learn More
-
- Also for servopneumatic applications/positioning with SPC200 and SPC11
- Connection: M5, G1/8, G1/4, G3/8
- Flow rate: 100 ... 2000 l/min.
- 5/3-way proportional directional control valve, normally closed
- Electronic throttle valve
- Setpoint module available as accessory
Learn More
-
- Port DN 13, 1/2"; DN20, 3/4"; DN25, 1"; DN32, 1 1/4"; DN40, 1 1/2"; DN50, 2"
- G-thread to DIN ISO 228-1 or NPT-thread to ANSI/ASME B 1.20.1 or Rc-thread to DIN 10226-2
- Medium pressure 0 ... 30 bar
- Valve function 2/2, NC (Normally Closed), NO (Normally Open), DA (Double Acting
- Suitable for nearly all media
- High chemical and thermal resistance
- ATEX-approval
Learn More
-
- Size 1" ... 4" or DN 25 ... DN 100
- Type of connection clamp, welded end, thread
- Nominal pressure range PN 10
- Manual actuation
- 2-way disc valve
- Seal material EPDM, FPM
- For controlling water and neutral liquids
Learn More
-
- Connection 1/4", 1/2", clamp
- G thread or NPT thread
- Pressure range 0 ... 6 bar
- Pneumatic actuation
- 2/2-way pinch valve
- Aluminium + stainless steel housing (Clean Design)
- Sealing material EPDM, NBR, silicone
- For controlling fluid/powder media, solids, and material mixtures
Learn More
-
- Piston spool and poppet valve technology from the MPA series
- Port M7
- Flow rate 230 ... 360 l/min
- Sub-base valve
- Solenoid actuated
- Signal status display with LED
- Integrated current reduction
- Manifold blocks
- Manifold sub-bases.
Learn More
-
- For decentralised drying of compressed air
- Port G1/2, G3/8
- Pressure 4 ... 16 bar
- Flow rate 40 ... 2000 l/min
- Reduction in pressure dew point 40 K
- Additional filtering of oil and particulates
- High flow rate
- Low purge air consumption and noise levels
Learn More
-
- More variants than in the standard
- Diameter: 12, 16, 20, 25, 32, 40, 50, 63, 80, 100, 125 mm
- Stroke length: 1 ... 500 mm
- Force: 51 ... 7363 N
- Double-acting
- Fixed/self-adjusting cushioning
Learn More
-
- System product for handling and assembly technology
- Diameter: 6, 10, 16, 20, 25 mm
- Stroke length: 10 ... 200 mm
- Force: 34 ... 590 N
- Position sensing
- Fixed cushioning
- Recirculating ball bearing guide
Learn More
-
- The standard stopper cylinder for all applications
- Diameter 16, 20, 32, 40, 50 mm
- Stroke length 5 ... 30 mm
- Permissible impact force on the advanced piston rod 880 ... 6280 N
- Position sensing
- Fixed cushioning
- Variants: trunnion, roller, non-rotating
Learn More
-
- Diameter 32 and 80 mm
- Stroke length 20 ... 40 mm
- Permissible impact force on the advanced piston rod 480 ... 14600 N
- Position sensing
- Fixed cushioning
Learn More